• AY McDonald 4424-100 2069C 1 1/2 Clear Silent Check Valve
Rubber Hose Coupling: Valves are designed to fit on standard sump pump line connections. Easy to install over 1 1/2" PVC pipe (schedule 40 or 80), steel pipe, or copper tubing. One piece housing construction, no gasket to fail or leak. Housing is.
  • Eliminates the typical hammering of a sump check valve after the pump cycles
  • All valves are pressure tested to ensure Leak-proof performance
  • Stainless steel clamps included.
  • It has 12 months warranty

Write a review

Note: HTML is not translated!
    Bad           Good

AY McDonald 4424-100 2069C 1 1/2 Clear Silent Check Valve

  • $38.92
  • $35.61



Related Products

Zoeller 57-0001 M57 Basement High Capacity Sump Pump

Zoeller 57-0001 M57 Basement High Capacity Sump Pump

Zoeller57-0001 M57BasementHighCapacitySumpPumpCorrosion resi..

$322.65

Zoeller 98-0001 115-Volt 1/2 Horse Power Model M98 Flow-Mate Automatic Cast Iron Single Phase Submersible Sump/Effluent Pump
Zoeller 53-0001 M53 Mighty-Mate Automatic Submersible Pump, 115-Volts

Zoeller 53-0001 M53 Mighty-Mate Automatic Submersible Pump, 115-Volts

Zoeller M53 Mighty-mate Submersible Sump Pump, 1/3 Hp1/3 H.P..

$248.30

Red Lion RL-SC50T 1/2-HP 4300-GPH Sump Pump with Tethered Float Switch, Cast Iron

Red Lion RL-SC50T 1/2-HP 4300-GPH Sump Pump with Tethered Float Switch, Cast Iron

Red Lion RL-SC50T 1/2-HP 4300-GPH Sump Pump with Tethered Fl..

$212.80

Red Lion Rl-SC50V 1/2 HP Cast Iron Sump Pump with Vertical Switch

Red Lion Rl-SC50V 1/2 HP Cast Iron Sump Pump with Vertical Switch

Pmp Sump W/flt 1/2hpAutomatic sump pumpHeavy-duty cast iron ..

$177.93 $249.99

Zoeller 508-0005 Aquanot 508 Sump Pump System Battery Back-Up System

Zoeller 508-0005 Aquanot 508 Sump Pump System Battery Back-Up System

Zoeller 508-0005 Aquanot 508 Battery Back-Up System12 volt h..

$499.35 $520.36

Liberty Pumps SJ10 1-1/2-Inch Discharge SumpJet Water Powered Back-Up Pump

Liberty Pumps SJ10 1-1/2-Inch Discharge SumpJet Water Powered Back-Up Pump

Liberty Pumps SJ10 1-1/2-Inch Discharge SumpJet Water Powere..

$284.35 $288.00

Liberty Pumps 257 1/3-Horse Power 1-1/2-Inch Discharge 250-Series Cast Iron Automatic Submersible Sump/Effluent Pump with VMF Switch
Liberty Pumps 287 1/2-Horse Power 1-1/2-Inch Discharge 280-Series Automatic Submersible Sump Pump with VMF Switch
Liberty Pumps 237 1/3-Horse Power 1-1/2-Inch Discharge 230-Series Automatic Submersible Sump Pump with VMF Switch

Liberty Pumps 237 1/3-Horse Power 1-1/2-Inch Discharge 230-Series Automatic Submersible Sump Pump with VMF Switch

Liberty Pumps 237 1/3-Horse Power 1-1/2-Inch Discharge 230-S..

$185.84 $186.44

AY McDonald 4424-101 2069C 2 Clear Silent Check Valve

AY McDonald 4424-101 2069C 2 Clear Silent Check Valve

Eliminates the typical hammering of a sump check valve after..

$40.39 $49.16

Wayne ESP25 12 Volt Battery Back-Up Sump Pump System with Audible Alarm

Wayne ESP25 12 Volt Battery Back-Up Sump Pump System with Audible Alarm

12v. Pumps up to 3300 gph at 0'. Reinforced thermoplastic ba..

$359.03 $381.00

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.