Electrical Characteristics
1.Solar panel: 0.55W
2.Li-ion battery: 3.7V 1200mAh
3.LED power: 0.2W, 5000K-5500K,12PCS, 22-24lm/PCS
4.Motion angle and distance: 120degrees, 10ft
5.Weight:5.32ounces
6.Size: 4.9*3.8*1.9inches
7.Working mode: Automatically turn off after lighting around 30s

Product Features
1.No dim mode, designed for home security and longer product life.
2.Integrated design of PIR motion sensor and night sensor.
3.Recharged by Sunlight and store power for overnight lighting.
4.Over 12 hours lighting time after 8 hours charged under ideal bright sunlight.
5.Waterproof IP 65 and durable.

Operation Instructions
1.Charge before first time use
Please take off the protective films first, then charge the solar light by placing it under the direct sunlight for about 5 hours.
2.Unlock and activate the solar light
Please use supplied key pin to click the "on/off" switch hole and unlock the lighting system.
3.How to Install the device?
Please use the supplied expansion pillar-hinge and screw to mount the device on pole or wall and anywhere outside you want for lighting.
4.Charge via solar panel
Please make sure that the product is installed in a place where can receive good direct sunlight without any shelter.
5.Night sensor function
At night or in darkness, this light will auto turn bright once human movement is detected by the PIR motion sensor.

Two steps easy to check whether the light can work or not
1. Unlock the product, charging the light by direct sunlight around 8 hrs.
2. Cover the solar panel with your hand, if the light is on, the product is working.

Special Note
1.Please fully charge the device for 2 or 3 sunny days before first use.2.Two modes: on/off. NO DIM MODE.

Package Content
4 x Baxia Solar Motion Sensor Light
4 x Expansion pillar-hinge
4 x Screw
4 x Key pin
4 x Manual

  • [Invisible Switch] The "on/off" hole was designed for waterproof reason. Just use the supplied key pin to insert the switch hole. When hearing the "click", the lighting system is unlocked.
  • [Motion Sensor & NO DIM MODE] To increase home security and product life span, this item was designed without dim mode. It will only be activated after movement is detected in dark then auto turns on. After lighting around 30 seconds, it turns off automatically.
  • [Ultra-Bright LED Lights] There are 12 powerful LEDs and the motion angle is 120 degrees which can provide excellent illumination and turn the dark space into a bright lighted space. It's a perfect choice to be used in garden, fence, patio, deck, yard, driveway, stairs, outside wall etc.
  • [High Efficiency and Eco-Friendly] This solar light is charged by exposuring to sunlight in day for around 8 hours. Then its rechargeable 1200mAh Li-ion battery can store the power for over 12 hours working time at night.
  • [Warranty Policy] We promise a 30-Day Money Back Guarantee and 90-Day Limited Product Warranty. Please feel free to contact us if any issue arise.

Write a review

Note: HTML is not translated!
    Bad           Good

BAXIA TECHNOLOGY LED Solar Lights, Wireless Waterproof Outdoor Motion Sensor Security Night Lights for Outside Wall, Garden,Driveway, Steps, Patio(...

  • $79.99
  • $37.99



Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.