NEW 12V HEAVY DUTY MACERATOR PUMP Product Description: 12V macerator pump now has a fully sealed motor and more powerful chopper blades. Also the 4 blade choppers reduce clogging. 12GPH flow rate will empty a 30 gallon holding tank in 3 minutes. Inlet 1 1/2"- discharge 1. Sealed Macerator Self-Priming Macerator Pump Waste Evacuation This macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage. Fish Box and Livewell Tank Evacuation This Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties. Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again this macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats. Dimensions: 11" x 3.5" x 3.5"
- 12V macerator pump now has a fully sealed motor and powerful chopper blades.
- Inlet 1 1/2"- discharge, Self-Priming Macerator Pump
- 12GPH flow rate will empty a 30 gallon holding tank in 3 minutes.
- Duty cycle of the pump is 15 minutes continuous
- This will reduce the possibility of a continued build up of sediment in the tank.
12v Macerator Sanitation Water Pump 45 Lpm 12 gpm RV Marine Boat Waste DC Toilet
- Brand: Seaflo.us
- Product Code: B011W1HG7U
- Availability: 20
Dynamic HeadThe effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.
Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.
If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.
If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure. Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance. For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.