• Johnson Pump (32-47258-003) 600 GPH Ultima Bilge Pump
Ultima Bilge PumpUltimaBilge Pumps are the latest addition to the Johnson Pump brand lineup. Integration of the Ultima "field effect" sensing technology into the bilge pump body creates a sleek reliable and pact unit with integrated switch ready to install and run for years and years of unerring service. Available in 600-800-1000-1250 GPH versions. Voltage 12 V DC. For UltimaBilge 600 GPH-1000 GPH we have easy-to-install Dura-Port discharge ports to eliminate stress cracking caused by over-tightened hose clamps. These pumps will be delivered including both a straight and a 90 degree smooth elbow Dura-Port. All version are delivered with a removable check valve.The Ultima Bilge pumps may be manually operated via the Johnson Pump bilge control panel.CE-ApprovedFeatures:Compact all-in-one unitIntegrated Ultima Switch sensing right into the pump body No MercuryRemovable clip on basket designRemovable impeller cover allows for easy clean out3-wire device can be run in auto or manual override mode No tools needed for maintenanceExtremely energy efficientWater-cooled motor for long service intervalsMeets the international standard ISO 8849 marinePump Body: ABSShaft Seal: Lip SealShaft: Stainless steelVoltage: 12 V DCCapacity 3 ft (0.9 m) head (13.6 V): 32 l/min - 500 GPHCapacity straight (13.6 V): 38 l/min - 600 GPHAmperage: 2.5 AFuse Size: 5 AConnection: 3/4"Length:142 mm - 6"Width:82 mm - 3.2"Height:105 mm - 4.1"Weight:0.66 kg - 23.3 oz. Product : JOHNSON PUMP ULTIMA BILGE 600 GPH 3/4" HOSE DURA PORTS Manufacturer : JOHNSON PUMP Manufacturer Part No : 32-47258-003 UPC : 729321472586
  • Johnson Pump (Mayfair) 3247258003, JPI3247258003

Write a review

Note: HTML is not translated!
    Bad           Good

Johnson Pump (32-47258-003) 600 GPH Ultima Bilge Pump

  • Brand: Johnson Pump
  • Product Code: 3001.3792
  • Availability: 20
  • $80.99
  • $80.92

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.

eXTReMe Tracker