Energy saving up to 60% with new frequency technology . It is used for clean or slight dirty pond water with the temperature from 4℃ to 35℃.
As an amphibious pump with the rustless ceramic shaft,apply to ponds,rockey,aquarium fish tank with water recycling equipment,waterfalls,garden foundations and other application.
Low-noise design, it won't disturb your lovely fish and your normal life.

ECO saving and generates more power with less energy consumption.
Great for both fresh and salt water applications and can be used in either wet or dry applications.
Easy access cover allows ease of maintenance of rotor, shaft and removable impellers.
This pump will automatically cut up the power when there is no water or the rotor was blocked.
Flow rate is adjustable Safe for fish(no copper, no oil).
Ceramic shaft,corrosion resistant in salt water
This product realize free tool demonstration,easy to clean.

Inout voltage:115V-60Hz
Power consumption: 70W
Delivery head(max): 18FT
Flow rate(max): 2100GPH
Hose connection: 3/4", 1", 1.25"
Length of the power cable: about 16.4FT
Weigth: 7.1LB
Dimension: 7.5 x 6x 5 inches

Package includes:
1. water pump
2. A set of connections
3. User manual(English)
  • Apply to ponds rockey,aquarium tanks with water recycling equipment matching,large flow and super silence
  • Use ceramic shaft,wear resistance,no rust and long service life. Both fresh and seawater,do not contain copper element
  • The locked rotor protection function(immediately cut off power after impeller jamed). Plug in again to restart
  • 115V/60Hz;Power 70W; Max flow 2100GPH(Adjustable); Max lift 18FT
  • Power cord length 16.4FT with UL plug;Hose adapter: 3/4",1",1-1/4"

Write a review

Note: HTML is not translated!
    Bad           Good

EXTRAUP 2100GPH Electric Adjustable Flow Garden Sumbersible Fountain Pond Filter Silent Pump for Fish Pet Aquarium Tank Waterfall Koi Salt Clear Water

  • Brand: EXTRAUP
  • Product Code: 4346781353
  • Availability: 20
  • $159.90

Related Products

Tetra Pond Rubber Tubing 1.25in, 20ft

Tetra Pond Rubber Tubing 1.25in, 20ft

Tetra 1 1/4 in ID Pond Tubing easily connects to pumps, bio-..


Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.

eXTReMe Tracker