• Flotec FP0012-6U-P2 Universal Discharge Hose Kit, 24-Feet by 1-1/4-Inch or 1-1/2-Inch
About the Flotec FP00126U Sump Pump Universal Discharge Hose, 24#39; The Flotec FP00126U makes working with your sump pump easy. This universal discharge hose is 24rsquo; long and ready to install for use with any sump pump. Therersquo;s no need to worry about tricky set up that could lead to disasters. In just minutes yoursquo;ll have the Flotec FP00126U installed and ready to go for either temporary purposes or permanent use. Whether you need to remove a sump pump area or a flooded area, this product will make your work as easy as possible. It comes with a steel hose clamp to make for a completely secure attachment to the pump and a corrugated hose and adapter to fit any type of pump you may have. The Flotec FP00126U is made of highquality materials that you can trust. Regardless of the project you need it for, this universal discharge hose is sure to deliver excellent performance and make your work as easy as possible.
  • Universal, Fits 1-1/4" or 1-1/2"
  • Ideal for pedestal pump discharge
  • Works with submersible sump pumps
  • Ready to install for emergency or permanent use
  • Hose clamp included,1-1/4" and 1-1/2" high-impact NPT barbed adapters

Write a review

Note: HTML is not translated!
    Bad           Good

Flotec FP0012-6U-P2 Universal Discharge Hose Kit, 24-Feet by 1-1/4-Inch or 1-1/2-Inch

  • Brand: Flotec
  • Product Code: FP0012-6U-P2
  • Availability: 20
  • $55.07



Related Products

Laguna Max-Flo 2900 Electronic Waterfall & Filter Pump

Laguna Max-Flo 2900 Electronic Waterfall & Filter Pump

Laguna Max-Flo Waterfall/Filter Pump , Is A High Performance..

$369.99 $523.81

Superior Pump 92333 1/3 HP Thermoplastic Pedestal Sump Pump

Superior Pump 92333 1/3 HP Thermoplastic Pedestal Sump Pump

FeaturesPedestal sump pumps 0.33 hp For use in sump basins 1..

$106.36

Superior Pump 92341 1/3 HP Cast Iron Sump Pump Side Discharge with Vertical Float Switch

Superior Pump 92341 1/3 HP Cast Iron Sump Pump Side Discharge with Vertical Float Switch

1/3HP split capacitor motor - high efficiency - low draw, 10..

$159.49 $162.04

Superior Pump 92372 Thermoplastic Sump Pump with Vertical Float Switch, 1/3 HP

Superior Pump 92372 Thermoplastic Sump Pump with Vertical Float Switch, 1/3 HP

1/3HP split capacitor motor - high efficiency - low Amp draw..

$133.16

Flotec FPOS1775A Flotec 1/4 HP 1790 GPH Utility Pump

Flotec FPOS1775A Flotec 1/4 HP 1790 GPH Utility Pump

Pentair FPOS1775A Flotec 1/4 HP 1790 GPH Utility PumpUtility..

$210.16

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.