• Hydrologic 27020 Reverse Osmosis System Float Valve

We always aim to provide the best water filtration and purification products for our clients, and work hard to retain our reputation as the number one resource for personal, professional, world class service providers. Our products are well known for our focus on the clients and the quality we provide to the users and it has become one of the most trusted names.

The Evolution 1000GPD Reverse Osmosis system is the leader in tankless RO systems. Capable of producing more than 1,000 GPD or 42 gallons per hour of pure water. Remove 95%+ of all Parts Per Million from your tap water Save more water by running a 2:1 waste to product water ratio, or optional 1:1 ratio (included)

Features
  • Reverse Osmosis System Float Valve
  • Standard sediment pre-filter included with system
  • Pleated and cleanable
  • Replacement Sediment Filter for Hydrologic Stealth 100 or 200 Series Reverse Osmosis Systems

  • Keeps water at appropriate levels in your RO system
  • Helps minimize the risk of your system reservoir flooding
  • Genuine OEM Product
  • Made in the USA
  • This is an O.E.M. part

Write a review

Note: HTML is not translated!
    Bad           Good

Hydrologic 27020 Reverse Osmosis System Float Valve

  • Brand: Hydrologic
  • Product Code: 27020
  • Availability: 20
  • $22.30


Available Options



Related Products

Hydrofarm AAPA15L 6-Watt 15-LPM Active Aqua Air Pump with 4 Outlets

Hydrofarm AAPA15L 6-Watt 15-LPM Active Aqua Air Pump with 4 Outlets

AAPA15L Features: -Air pump. -With 4 outlets, 15L per minute..

$34.74

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.