Finally a stronger but quiet pump. The Jebao 388 pump can go to 185 gallons per hour and has a maximum head (lift) of 59 inches. However, it is best suited for a fountain that needs the water to only lift to about 40 inches (3'4"). At 59" there will be no force. PERFORMANCE: A) 185 GPH @ 0.7 FT B) 161 GPH @ 1.3 FT C) 132 GPH @ 2.0 FT D) 134 GPH @ 3.3 FT E) 63 GPH @ 4.6 FT F) 0 GPH @ 4.9 FT Replacement cross-reference Peaktop PT-505 and PT-606, Fountain Tech FT160, Fountain Pro WT170, (12 volt version WA170LV); Peaktop; AP1320 Zhen Hua Electrical Appliance Co., LTD, HI-1000 pump
  • 120V AC Jebao water pump with flow control
  • Max flow rate: 105 gal/hour (400 liters/hour)
  • Max head: 26"
  • Pump Size: 2"x1.5"x2"(H)
  • 6" round electrical cord with 3-Prong Plug

Write a review

Note: HTML is not translated!
    Bad           Good

Jebao PP388/AP-388 Submersible Fountain Pump 198GPH

  • Brand: Jebao
  • Product Code: PP-388
  • Availability: 20
  • $60.21

Related Products

Jebao Pp300Lv Water Pump 40 GPH

Jebao Pp300Lv Water Pump 40 GPH

Pump is fully functional with transformer and power cord - j..


Jebao Ap-399 Submersible, Hydroponics, Aquaponics, Fountain Pump, 264 GPH, 18W

Jebao Ap-399 Submersible, Hydroponics, Aquaponics, Fountain Pump, 264 GPH, 18W

Powerful compact pump . Hysteresis (often confused for Mag D..


Jebao WP1500 Submersible, Hydroponics, Aquaponics, Fountain Pump 400gph, 25w

Jebao WP1500 Submersible, Hydroponics, Aquaponics, Fountain Pump 400gph, 25w

PERFORMANCE:\nA) 400GPH @ 0 FT\nB) 303GPH @ 1.6FT\nC) 238 GP..


Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.