This solid diaphragm style pump structure is simple and small, making it fit well in many style of wells and water systems, it does not displace too much water.
Weighing just 3 kg, it is easy for most people to handle.
Installation is simple and fast. The "quick disconnect" feature allows the pump to be easily separated from the tube via the patent pending "Watertight-Gland" design. Quickly control the pump when maintenance is needed.
Even if your well runs dry or you need to test in dry conditions, no damage will be done to this durable pump!
The positive displacement, 3 chamber solid design diaphragm pump is run by a permanent magnet thermally protected motor.
The stainless steel fastener and 50 mesh stainless steel inlet screen are long lasting and non-corrosive.
The housing is also corrosion proof, for a pump that will last for years and years in many conditions and environments.
With a flow rate of 61 pm, this is an efficient pump for most watering needs. The maximum lift is 230 feet, which is sufficient for most wells and situations.
1.6 gpm (Gallons per Minute) flow rate
solid diaphragm structure
230 ft maximum lift
100 ft maximum submersible depth
solar power possible
3 kg weight
stainless steel fastener
stainless steel inlet screen
orange color housing

  • Perfect for cabins, livestock ponds, off-grid living, Permanent magnet thermally protected motor
  • 50 mesh stainless steel inlet screenStainless steel fastener,
  • Up to 230 feet lift, Solar power possible, energy efficient,
  • Flow Rate: 1.6 GPM (6 Liters per Minute), Fitting: 1/2" Barbed Fitting

Write a review

Note: HTML is not translated!
    Bad           Good

Farm & Ranch 12v / 24v Submersible Deep Dc Solar Well Water Pump, Solar, Battery, Alternate Energy, 230ft+ Lift

  • $187.76



Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.