• Seaflo 12v DC Water Pressure Diaphragm Pump 18.9 L/Min 5.0 Gpm 60 Psi
Features & Benefits:

Positive displacement pump
Capable of being run dry
Quiet operation Industry standard mount pattern Demand pump
Easy connect fittings

Typical Applications:

Agricultural Spraying, General Industrial, Automotive Marine/RV PUMP

Specification:

Duty Cycle: Continuous Voltage: 12V
Rating AMPS: 8A
Max. AMPS Draw: 17.0 A
lift Mode: Demand
Max Pressure: 60 PSI (4.2 bar)
Open Flow(Max. Flow): 5.0 GPM (18.9LPM)
Liquid Temperature: 140°F (60°C) Max.
Priming Capabilities: 6 feet (1.8 m) suction
Inlet/Outlets Ports: 1/2" NPT, 13mm pyramid hose barb
MOTOR Leads: 16 AWG, 4.5" long with 2-Pin connector/ Leads
Dimension: 8.72" (Length) X 5.20" (Height) X 5.75" (Width)
Weight: 7 lbs (3.17 kg)

Warranty:

One year limited product warranty.

  • The patented design delivers smooth & consistent flow at all ranges of operation, while drawing low current.
  • The balanced motor design incorporates precision ball bearings for long life, motor is equipped with an integral thermal breaker.
  • Open Flow(Max. Flow): 5.0 GPM (18.9LPM); Max Pressure: 60 PSI (4.2 bar); Power for the Pump: DC 12V, Rating AMPS: 8A, Max. AMPS: 17A;
  • Professional Grade Pump - Ideal for Automotive Marine/RV/Caravans, Agricultural Spraying, General Industrial, Sprayer fixtures
  • Sealed pressure switch automatically turns the pump off when pressure builds up such as turning off the tap & will automatically turn back on when you turn the tap back on

Write a review

Note: HTML is not translated!
    Bad           Good

Seaflo 12v DC Water Pressure Diaphragm Pump 18.9 L/Min 5.0 Gpm 60 Psi

  • Brand: Seaflo
  • Product Code: unknown
  • Availability: 20
  • $131.00



Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.