• Seaflo 60 PSI Washdown Deck Wash Pump KIT 12v 5.0 GPM for Caravan Rv Boat Marine Yacht
Introduction:

Seaflo's washdown kit includes everything you need for tough washdown applications all in one box. The kit includes the NEXT Generation SEAFLO Pump, Fittings, Nozzle, Raw Water Strainer and 25' coiled hose.

Technical Parameters:

1.Voltage: 12V DC
2.Flow capacity: 18.9 Litres per minute (5.0 Gallons per minute)
3.Water pressure: 60 PSI (4.1 bar)
4.Nozzle open pressure: 55 PSI (3.8 bar)
5.Hose Outlets: Suits 12mm (1/2") diam. hose ,1/2"-14 MNPT
6.Twin core wire
7.Current Draw: 18.0 Amp (max. 20 Amp)
8.Dimensions: Length 221mm x Width 146mm x Height 132mm
9.Approvals: CE
Features:

1.Beware of inferior non-genuine products on the market that claim to be just as good
2.Complete washdown pump kit with spray nozzle and coiled hose
3.Powerful 5-chamber positive displacement diaphragm pump, for smooth and quiet flow
4.Self-priming 12V pump
  • For marine, RV, and recreational deck wash applications Suitable use with for fresh water or saltwater Designed for intermittent use only. Duty cycle: 30 mins
  • Professional grade pump - Ideal for cleaning boats, fish boxes, anchor wells, dinghies and caravans Multi-step corrosion protection and seamless motor body for enhanced protection
  • Rubber mounting feet for corrosion protection and noise reduction Santorprene diaphragm - Can run dry without damage
  • Thermal overload and ignition protection Easy connecting system
  • Heavy duty washdown pump Trigger nozzle with quick connect Quick connect adaptor UV-protected 7.5M (25') coiled hose

Write a review

Note: HTML is not translated!
    Bad           Good

Seaflo 60 PSI Washdown Deck Wash Pump KIT 12v 5.0 GPM for Caravan Rv Boat Marine Yacht

  • Product Code: unknown
  • Availability: 20
  • $155.07



Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.




PondPumpsCanada.ca is a participant in the Amazon Services LLC Associates Canadian Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to the Amazon.ca marketplace. Product description, photographs and reviews and other various content that appears on our website comes from Amazon Services LLC. This content is Provided ‘AS IS’ and is subject to change or removal at any time.


PondPumpsCanada.ca - A Proud Canadian Website.

© 2018