Runs automatically, no battery or electricity needed, just the sunshine Max. Water Height: 30-60cm Maximum Flow: 160 L/H Lifetime: 20000 hours Solar panel:7V/1.2W. Pump:4.5-12V Installation: Put the pump totally in water with nozzle above the water Make sure the pump is fixed firmly on the bottom of pool to avoid vibration Plug jack of pump into the jack of solar panel output Lay the solar panel on the ground where sunlight is most accessible Note: This pump comes with NO power storage function, so it will work only when there is sunlight to provide solar power and will not work when there is no sunlight.

Packing list as follows:
1 x Solar pump
4 x Spray nozzles
3 x connection accessories
1 x english user's manual
  • Solar powered fountain pump kit for fountains, waterfalls and water displays
  • Runs automatically, no battery or electricity needed, just the sunshine / Features a square solar panel to be staked on the ground
  • Create a relaxing environment in your garden
  • Cable Length: Approx.129 inch (3.3m) / 3 spray nozzles included
  • Submersible pump with suckers at the bottom / Easy to set up by yourself

Write a review

Note: HTML is not translated!
    Bad           Good

1.2 Watt Solar Power Water Pump Garden Fountain - for fountains, waterfalls and water displays

  • $18.60



Related Products

Anself 9V 2W Solar Power Water Pump for Landscape Pool Garden Fountains

Anself 9V 2W Solar Power Water Pump for Landscape Pool Garden Fountains

Product Performance: 1. The pump is driven directly by the s..

$28.99

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.