• Kingda 1.5W Outdoor Solar Fountain Pump Waterfall for Pool Garden Pond Bird Bath Decorative Submersible Kit Water Pump
Built a solar powered bird bath with Lewisia Solar Water Fountain. You're absolutely thrilled about this new addition to your garden.

It has two short legs so you can angle it toward the sky without laying it down flat.

Specification:
Solar panel: 6V/1.5W
Brushless pump input: DC 4.5-10V
Maximum water flowing: 175L/h
Maximum lift: 85cm
Maximum water height: 55cm
Lenght of kit: 3.5cm
Cable Length: 10 feet / 3m
Solar Panel Size: 5.5*5.1 inch / 14*13cm
Water Pump Size: 1.6*1.4*1.5 inch / 4.1*3.6*3.8cm
Net weight: 0.8lb / 0.36kg
Without on/off switch.

Note:
Make sure that you submerge the solar water pump in water before you expose it to sunlight because it turns on IMMEDIATELY with CONSTANT, DIRECT sunlight. You will love this little marvel! It will not continue at night.

If you don't want the water to splash out of the bird bath, took the "spray cap" off (leaving the funnel shape piece uncapped) so it's more of a bubbler.
  • Long Cable Length: 10 feet cord from the pump to the solar panel so you can have the birdbath in the shade but the panel in the sun
  • Multiple spray pattern options: Different fountain heads to customize the water patterns you want.
  • Easy to Install & Clean --- No tools required, totally hassle-free.
  • The Solar Birdbath Pump sprays IMMEDIATELY once the sunlight hits the solar panel (CONSTANT, DIRECT sunlight).
  • Great for bird bath, fish tank, small pond, garden decoration, water circulation for oxygen, etc.

Write a review

Note: HTML is not translated!
    Bad           Good

Kingda 1.5W Outdoor Solar Fountain Pump Waterfall for Pool Garden Pond Bird Bath Decorative Submersible Kit Water Pump

  • Brand: TSSS
  • Product Code: PQ06
  • Availability: 20
  • $56.06



Related Products

Anself 9V 2.5W Solar Power Panel Water Pump for Landscape Pool Garden Fountains Decorative

Anself 9V 2.5W Solar Power Panel Water Pump for Landscape Pool Garden Fountains Decorative

Features: CE、RoHS testing approval. Suitable for bird bath, ..

$31.99

Dynamic Head

The effect of the Earths gravity on the "lift" or head pressure is fairly simple; for every vertical foot of distance the pump moves the water you are adding one foot of head pressure so the ratio is a 1:1 ratio. The effects of the friction, caused by water as it travels through your hose or pipes, on the total head pressure is a little more difficult to calculate especially as there are slight variations in pipe friction in different hose materials and the smoothness of the inner bore. Basically. for every ten feet of pipe through which the water has to travel travel horizontally will contribute 1 foot of head height; the ratio of the pipe friction loss is a 10:1 ratio.

Plumbing fixtures and bends and corners in your hose also increase the total head you must calculate to ensure the proper final volume from your pump. Every corner with a 90 degree elbow in your plumbing will add 1 foot of head pressure  with a 1:1 ratio. 45 degree elbows, tees and even insert couplers can all have an impact on the final flow.

If you install a pump 40 feet away from the top of your waterfall which is 6 feet above the pump and the tubing is a single run of 40 feet horizontally then you add 4 feet of head for the tubing length (the 10:1 ratio) to the 6 foot differnetial between the pump location and the final height of the waterfall so your final total dynamic head calculation would be 10 feet. This means your final volume of water flow in this water feature or application would be the volume of flow on the performance curve that equaled the gallons per hour at 16 feet. This volume will certainly be much less than the initial volume the pump can move at an open flow or a zero head.

If in the above example your 40 feet of horizontal tubing run also required 3 elbows of 90 degrees then an additional 3 feet of theoretical head would be added and your final flow result would be at 19 feet on the performance curve of the pump. In this example you would want to choose a pump that has the desired GPH rating at 9 feet of head pressure.  Tubing size is also an important factor in accounting for head pressure loss, in general you should never reduce the diameter of the tubing below what the output size of the pump is, this will drastically increase head pressure, and reduce pump performance.  For maximum pump performance, using the largest tubing that is practical is the best choice. A best practice is to use a hose with an inner diameter that is the same as your pumps outlet fitting.